Types of Tile Spacers: Cross, T, Wedge, Horseshoe and Leveling Spacers

Walk down any tile aisle and you will find a bin of small plastic shapes: crosses, Ts, wedges, horseshoes and clips. All of them are tile spacers, and each one solves a slightly different problem. Picking the right type is the difference between joints that run straight and a floor that drifts out of line halfway across the room. This guide covers the types of tile spacers, what each is for, how to place them and when you need a leveling spacer instead of a plain one. If you only want the short version of plain spacers versus levelers, read tile spacers vs. tile leveling spacers.

What are tile spacers?

Tile spacers are small plastic pieces placed between tiles to keep every grout joint the same width while the mortar cures. They are sold by joint size, such as 1/16, 1/8 or 3/16 inch, and come in several shapes, each suited to a different layout or job.

Spacers are also called tile separators or tile gap spacers. Their only job is spacing: they control the gap between tiles, not the height of the tile edges. That is why leveling spacers, which do both, are treated as a separate type below. Whatever shape you choose, the joint size printed on the spacer should match the joint the tile maker and the grout allow.

Types of tile spacers at a glance

The five common types of tile spacers are cross spacers, T spacers, wedge spacers, horseshoe spacers and leveling spacers (clips). Cross and T spacers set joints in grid and offset layouts, wedges adjust gaps, horseshoes shim and space heavy pieces, and leveling spacers set the joint and keep edges flush.

TypeShapeBest forLevels edges?
Cross spacerPlus sign with four legsFour-way corners in grid layoutsNo
T spacerT with three legsThree-way joints, offset and running bondNo
Wedge spacerTapered stripAdjustable gaps, wall tile, perimeter gapsNo
Horseshoe spacerU-shaped shimShimming, wide joints, stone and heavy piecesNo
Leveling spacer (clip)Base under the tile, tab through the jointRectified and large format tile, narrow jointsYes, with a wedge or cap

Cross tile spacers

Cross spacers, also called plus spacers, sit where four tile corners meet in a straight grid. They are the most common tile spacer and work well for square tile in a stacked layout. Many installers stand them on end in the joint instead of flat at the corner so they are easy to pull out before grouting.

Laid flat at a corner, a cross spacer can get buried in mortar and become hard to remove. Placed upright in the joint, one leg does the spacing and the rest stays above the tile, so it comes out cleanly. Cross spacers do not work well in offset layouts, because the corners no longer line up; that is where T spacers come in.

T tile spacers

T tile spacers fit where three tiles meet, which happens in every offset, brick and running bond layout. They keep the long joint straight and the short joint the right width at the same time, without the extra leg a cross spacer would leave in the face of a tile.

T spacers are also useful along the first row against a ledger or wall, and at the edge of a backsplash. With plank and 12×24 tile in an offset pattern, they are a quick way to keep the pattern consistent, although on long tiles they do nothing about the edges bowing up or down.

Tile wedge spacers

Tile wedge spacers are tapered strips you slide into a joint until they stop. Pushed in farther, they open the gap; pulled back, they close it. That makes them handy for adjusting joints, holding wall tile from sliding, and keeping a perimeter gap at walls and fixed objects.

Plain wedge spacers should not be confused with the wedges of a leveling system. A leveling wedge locks into a clip and presses the tile faces flush; a wedge spacer only sets a gap. Next Level makes the second kind: reusable leveling wedges that work with Next Level clips.

Horseshoe spacers

Horseshoe spacers are flat U-shaped shims. Stood in a joint they space heavy or thick pieces, and laid flat under an edge they lift a tile or a stone piece to the right height. They come in a range of thicknesses and are often stacked for wider joints.

Because of their shape, horseshoe spacers can be slipped in and out from the side, which is useful for stone, window sills, countertops and wall tile resting on a bottom row. They level only by shimming, one point at a time, which is slow on a floor with many joints.

Leveling spacers and clips

Leveling spacers, or leveling clips, combine a spacer with a lippage control. The base slides under neighboring tiles, the tab sets the joint width, and a wedge or cap pulls the tile faces into the same plane. After the mortar cures, the top snaps off at the joint.

This is the type to use for rectified and large format tile, wood-look planks and any job with narrow joints, because those are the cases where edge height matters as much as joint width. Next Level makes leveling clips in 1/32, 1/16 and 1/8 inch, designed by real tile installers for ceramic and porcelain tile. The 1/32 inch clip is meant only for tile whose maker allows a joint that narrow, since the industry minimum is commonly 1/16 inch. To compare clip-and-wedge, spin cap and strap systems, see how to choose a tile leveling system.

Which type of tile spacer should you use?

Use cross spacers for a square grid, T spacers for offset and running bond layouts, wedge spacers to fine-tune gaps on walls and edges, horseshoe spacers for shimming and heavy pieces, and leveling clips whenever lippage is a risk, which includes most rectified and large format tile.

Joint size matters as much as shape. For ceramic and porcelain tile from 12×12 up to large format, 1/8 inch is a common joint when you want a narrow but visible grout line. The tile spacer size chart matches joint sizes to tile types, and ceramic and porcelain tile spacers covers warpage by material. Many jobs mix types: leveling clips across the field, T spacers on the first row and wedge spacers at the walls.

Frequently asked questions

Are tile separators the same as tile spacers?

Yes. “Tile separators” is another name for tile spacers; both keep the joint between tiles at a set width.

Do you leave tile spacers in when grouting?

No. Grout makers call for joints free of spacers before grouting. See how to remove tile spacers for timing and technique.

Can tile spacers be reused?

Plain spacers that come out clean can be reused if they are not bent or crushed. Leveling clips are single-use, while leveling wedges, such as Next Level wedges, are reusable.

Key terms

  • Plus spacer: another name for a cross spacer, the four-legged spacer used at grid corners.
  • Upright placement: standing a spacer on end in the joint so it is easy to remove before grouting.
  • Flat placement: laying a spacer flat at a tile corner, which can bury it in mortar.
  • Tapered wedge spacer: a strip that gets thicker along its length, used to set an adjustable gap.
  • Tile shim: a thin spacer placed under a tile edge to raise it, such as a flat horseshoe spacer.
  • Perimeter gap: the space left between tile and walls or fixed objects so the installation can move.
  • Three-way joint: a point where three tiles meet, typical of offset layouts and filled with a T spacer.
  • Spacer thickness: the width a spacer sets in the joint, printed as a fraction of an inch or in millimeters.

Sources

Ready to level, not just space? Next Level clips set 1/32, 1/16 or 1/8 inch joints and keep tile edges flush with reusable wedges. The Next Level tile leveling system ships nationwide, sold by quote. Request a quote for Next Level leveling spacers.

Elson Ribeiro
Elson Ribeiro is the owner of Next Level Tile Supplies in Tampa, Florida. He has 22 years of hands-on experience installing tile, and he designed the Next Level tile leveling system around the problems he saw on real job sites.
Tags :
Share This :

Take your tile installation to the Next Level!